It works very well for what it does, it is an anti-rust and scale-inhibitor. The CorQuest product from WoodMaster is an excellent product, it is a nitrate-based product. Boiler Maintenance Kits - Description and Costs CorQuest - WoodMaster This is another reason why an outdoor Wood Master furnace is the superior solution to heating your home. If creosote has accumulated it should be removed to reduce the risk of a chimney fire. The chimney connector and chimney should be inspected at least monthly during the heating season to determine if a creosote build up has occurred. When ignited this creosote makes an extremely hot fire. As a result, creosote residue accumulates on the lining. The creosote vapors condense in the relatively cool chimney flue of a slow burning fire. When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. Forest fires! Creosote Information and the Need for Removal: (coals can live for a week or so) Keep this in mind when disposing ash and coals. Ashes should be retained in the closed container until all cinders have thoroughly cooled. The closed container of ashes should be placed on a noncombustible floor or the ground, well away from all combustible materials, pending final disposal. Ashes should be placed in a metal container with a tight-fitting lid. If your furnace is not equipped with an ash auger system use a shovel to take ashes from the front of the firebox and use a rake to pull ashes from the rear of the furnace to create a level bed of hot coals. Remove ashes when the furnace is very low on wood. You will be surprised those coals will heat your home all day and then some. The best is a well-controlled fire and when the wood gets low, rake the ashes exposing buried unburned coals. Do not overfill the unit so hot coals fall out when opening the door. I recommend burning cut, split, seasoned wood. Once the furnace has reached 180 degrees, the furnace is ready to be filled to capacity. You might notice some water on the inside walls of the unit, this is normal the furnace is sweating like a cold drink on a summer day. Be sure pumps are circulating when firing the furnace. Build a small fire, and add wood as needed. Paper and kindling should be used for starting the fire. Once you have determined that there are no leaks and all looks good. The circulation pump will be very helpful in bleeding the air out. Open ball valve in back to see if the light goes out or check the over flow pipe with a flash light. Not a bad idea to check to make sure the light is working properly. Add water until it over flows the vent pipe on top of the unit. If the light is not lit, this indicates water level is low and the furnace may need to have water added. Routinely pay attention to the water level light. Moisture combined with ashes will eat through metal in a short time. If you have an ash auger, remove it, clean out all the ashes and scrape excess creosote from the fire chamber surface. Protect your fire chamber by placing the chimney cap over the chimney during the off season, inspect all silicon caulking and make sure it has a good seal so moisture can’t enter furnace. Add the treatment to vent (Small tube) on top of the unit. Add the boiler treatment that came with your unit or purchased from your dealer. Before adding boiler treatment, be sure that the water temperature is at least 100 degrees or higher. This should be done every year! Allow system to burn for 2 hours and then add boiler treatment as follows. Refill stove and add boiler treatment right away. Add water to furnace through the return lines. To flush - leave drain valve open and close pump valve. To drain furnace - open drain valve and let stove empty completely. It is very important to drain and flush your furnace each spring. Once the green light on the control panel goes on, you’re full. Make sure the ball valves on the unit are open to the return and supply. Start filling the unit inspect for leaks. This makes it much easier to fill and flush the unit. Regular Maintenance - Do It Yourself Tips Filling with Water:Ĭonnect your domestic water to the return line to the furnace using a ball valve. Additionally, you'll find out how experts respond to the most frequently asked questions from users on wood boiler installation and maintenance. Learn all the maintenance tips and tricks that your outdoor wood boilers need to be in great shape! Find out all about the products, boiler treatments, and scale inhibitors you can use for different types of boilers.
0 Comments
Leave a Reply. |